Ferments for 7 to 14 days and then distill
Heat water to 120 degrees F then add honey
Cool to 70F
Aerate by pouring mash back and forth between two buckets
Transfer to fermenter
Allow to ferment from 7 to 10 days
Siphon mash into still
Distill, make sure to throw out foreshots, heads, and tails
Make extremely tight heads and tails cut if you plan on drinking un-aged
Age for 2-3 weeks using lightly toasted american oak chips
Add a small amount of honey to the finished product
If the final product is a little cloudy then just pour thru a filter
Prep time: 5 minutes
Cook time: 10 minutes
Fermentation time: 2 weeks
Yield: 1.5 gallons 80 proof rum
Heat water to 120 degrees Fahrenheit stirring sugar in a pound at a time.
Add molasses, 1 jar at a time, once most of sugar has been dissolved.
Stir thoroughly while adding so molasses does not burn.
For a more mellow, smoother finished product, allow to cool to 70 degrees Fahrenheit and add bread yeast. Aerate, then transfer to carboys.
For a higher yield (but a more unpredictable finish) use “Super Start” yeast and ferment at 90F.
Install air lock and allow to ferment for at least 2 weeks.
Let it settle and then distill
Prep Time: 1 hour
Cook Time: 3 hours
Batch Size: 5 gallons of mash, 4.5 gallons of wash
Yield: 1 gallon of 100 proof spirit (1 quart of 100 proof hearts)
Rinse the strawberries with clean water: this will reduce the potential of an infection from wild yeast or bacteria on the strawberries.
Remove the green tops from the strawberries
Remove any rotten or spoiled strawberries
Put only good strawberries (free from rot and mold), without the tops, into a blender.
Blend the strawberries. Do Not Over Blend
Add raisins to the strawberries as you blend them until all 1.5 pounds of raisins have been incorporated into the batch.
Dump the strawberry puree into a sanitized bucket
Once 2.5 gallons of strawberry puree has been collected, transfer puree to a stainless steel boil kettle
Add 3 gallons of water to the 2.5 gallons strawberry puree. You should have 5.5 total gallons of strawberry mash at this point
Take a specific gravity reading of the mash, you will need to use a brix refractometer as the mash will be too thick for a hydrometer
The Strawberry mash should have a specific gravity reading around 1.024 which would yield around 3.5% ABV
Add sugar 1 pound at time until you reach a starting gravity of 1.054, as this will yield around an 8% starting alcohol (before distilling)
Make sure that you stir the mixture well after you add sugar and before you take another brix reading
Heat the Mash to 160 degrees
Once the mash has reached 160 degrees use a wort chiller to cool the mash to 70 degrees
Once the mash is at 80 degrees start making your yeast starter
Once the mash is cooled to 70 degrees transfer it to your fermentation vessel
Add the yeast starter to the fermenter
Add a sterilized airlock to the fermenter
Ferment in a dark place around 70 degrees for 7 days
Siphon (Youâ€™ll need to use 1/2? hose for this) the wash through a strainer (a fine cheesecloth, or a nylon paint strainer). Separate the pulp an discard it. Only add strained juice to the still. Youâ€™ll end up with about 4.5 gallons. Make sure not to add any of the settled yeast from the bottom of the fermenter to the still.
Complete a â€œstripping runâ€ by distilling the wash in a copper still using medium high heat. Distillate should be pouring out of drip tube. Do not make any cuts during the stripping run
Next, complete a â€œspirit runâ€ by distilling the product from the stripping run. Use medium low heat and run the distiller very slow (product should be dripping out of the still, not pouring). To be safe, make at least a 200 ml foreshots cut, and healthy heads and tails cuts, saving only the best part of the middle of the run for the hearts.
Discard the heads, along with the foreshots. Keep the hearts for the next step. Set the tails aside to use in future feints runs.
Pack pint jars with fresh sliced strawberries and fill them the rest of the way with the hearts from the spirit run.
Heat water to 70 degrees and then mix in malt and grain. While stirring the
mixture slowly heat to 160 degrees (raise temperature 5 degrees every 2
Keep mixture at 160 degrees stirring constantly for 2-3 hours to
convert starch into fermentable sugar and dextrin.
Filter off liquid and place into fermentation device and allow to cool to 70- 80 degrees.
Immediately pitch with 3 grams of yeast.
To avoid secondary fermentation and contamination add 1 gram of ammonium-fluoride.
Stir liquid for 1 minute then cover and seal with a airlock.
Mash will take 5-7 days to ferment.
After fermentation is complete pour into, still filtering through a pillow case to remove all solids.
Put corn in a burlap bag and wet with warm water. Place bag in a warm dark
place and keep moist for about ten days.
When the sprouts are about a 1/4″ long the corn is ready for the next step.
Wash the corn in a tub of water, rubbing the sprouts and roots off.
Throw the sprouts and roots away and transfer the corn into your primary fermenter.
With a pole or another hard object mash the corn, make sure all kernels are cracked.
Next add 5 gallons of boiling water and when the mash cools add yeast.
Seal fermenter and vent with a water sealed vent.
Fermentation will take 7-10 days.
When fermentation is done, pour into
still filtering through a pillow case to remove all solids.
Ferments for 7 to 14 days and distill.
Put enough feed to cover bottom of 5 gallon bucket a good 4 inches deep
Add 5 pounds of sugar.
Fill 1/2 full with boiling water.
Mix until sugar is dissolved.
Let it set for 90 minutes and then finish filling with cool water.
Add the yeast after it has cooled to the recommended temperature on the yeast label.
Cover with lid–our lid has a little cap that screws on, leave it loose to breathe. 4-5 days later it’s ready to run!
This is an old-timer recipe and very well. Should turn out to be 150-180 proof.
For pot stills you should filter it by pouring it through a pillow case into a 5 gallon bucket after it has finished fermenting. Otherwise the meal will settle and burn in the bottom of your still.
Some folks leave the solids in the pillow case and tie it off where it will not touch the bottom of the still.